WS3413H productdescription winsemi microelectronics winsemi microelectronics winsemi microelectronics winsemi microelectronics winsemi microelectronics c o p y r igh t @ w i n s em i microelectronics c o . , lt d . , a l l ri g h t r e s er v ed 1030 features ? internal 650v power mosfet ? active pfc for high power factor and low thd ? critical conduction mode operation ? system efficiency up to 95% ? without auxiliary winding ? excellent lin e and load regulation ? 3% led output current accuracy ? thermal regulation function ? led short/open protection ? current sensing resistor open protection ? auto fault recovery ? available in dip7 package applications ? e27 led bulb, spot light ? par30, par38 lamp ? t8/t10 led string ? other led lighting description the WS3413H is a high precision non-isolated buck driver with active pfc, specially designed for universal input offline constant current led lighting. the driver with on-chip pfc circuit achieves high power factor and low thd. operating in critical conduction mode, the power mosfet switching loss is reduced and the inductor is fully utilized . the WS3413H integrates a 650v power mosfet. with few external components, the led output current can be precisely controlled. the WS3413H offers rich protection functions to improve the system reliability, including led open circuit protection, led short circuit protection, cs resistor open circuit protection and cycle by cycle current limit. all the protection functions are auto-recovery. the system reliability is further improved by the thermal regulation function . the output current is reduced when the driver is over temperature. the WS3413H has u ltra low star t up current and u ltra l ow o perating c urrent . the WS3413H is a vailable in dip7 package . typical application non-isolated buck apfc offline led driver
www.winsemi.com tel : +86-755-8250 6288 fax : +86-755-8250 6299 2 / 8 WS3413H productdescription winsemi microelectronics winsemi microelectronics winsemi microelectronics winsemi microelectronics winsemi microelectronics pin configuration and marking information the WS3413H is a vailable in dip7 package the top marking is shown as below: pin definition name pin no. description comp 1 loop compensation node. this pin connects a capacitor to gnd for stabilization of the control loop, achieving accurate led current, high power factor and low thd. gnd 2 ground . vcc 3 power supply p in. connect a bypass capacitor from this pin to gnd. fb 4 feedback voltage input p in. this pin detects the inductor demagnetization signal and the output voltage. d 5 / 6 internal hv p ower mosfet d rain . cs 7 current sense p in. c onnect a resistor to gnd to sense the inductor current. internal block diagram WS3413Hd7p a product code x internal code bcy internal code for qc y mx d/c
www.winsemi.com tel : +86-755-8250 6288 fax : +86-755-8250 6299 3 / 8 WS3413H productdescription winsemi microelectronics winsemi microelectronics winsemi microelectronics winsemi microelectronics winsemi microelectronics ordering information package marking part number 7 -pin dip-7 , pb-free WS3413Hd7 p WS3413Hd7 p recommended operation conditions part number package input voltage maximum output power WS3413H d7 p dip7 175vac-264vac 120v/240ma 90vac-264vac 80v/240ma absolute maximum ratings symbol paramete range unit v cc vcc pin voltage -0.3~8 v v d internal hv mosfet drain to source voltage -0.3~ 650 v v cs current sense pin input voltage -0.3~7 v v fb feedback pin input voltage -0.3~7 v v comp compensation pin voltage -0.3~7 v p dmax power dissipation 0. 9 w t j operating junction temperature 1 65 t stg storage temperature range -55~1 65 note : stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device.
www.winsemi.com tel : +86-755-8250 6288 fax : +86-755-8250 6299 4 / 8 WS3413H productdescription winsemi microelectronics winsemi microelectronics winsemi microelectronics winsemi microelectronics winsemi microelectronics electrical characteristics (unless otherwise specified, vcc=8v and ta =25 ) symbol parameter conditions min typ max units supply voltage section v cc_clamp vcc clamp voltage 7. 5 8. 0 8.5 v i cc_clamp vcc clamp current 5 ma v cc_st vcc turn on threshold vcc rising 7.07 7.57 8.07 v v uvlo_hys vcc turn off hysteresis vcc falling 1. 32 v i st vcc startup current vcc www.winsemi.com tel : +86-755-8250 6288 fax : +86-755-8250 6299 5 / 8 WS3413H productdescription winsemi microelectronics winsemi microelectronics winsemi microelectronics winsemi microelectronics winsemi microelectronics application information the WS3413H is a high precision active pfc driver integrating 650v power mosfet, specially designed for non-isolated buck offline constant current led lighting. operating in critical conduction mode, the driver achieves high power factor, low thd and high efficiency. start up after system powered up, the vcc pin capacitor is charged up by the start up resistor. when the vcc pin voltage reaches the turn on threshold, the internal circuits start working . t he comp pin voltage is pulled up to 1.5v quickly, then the WS3413H starts switching . the system works at 10k hz frequency at the beginning, the comp voltage rises up gradually, and the inductor peak current also rises up. the led current hence achieves a soft start without overshoot . after the output voltage is built up, the vcc power is supplied by the output voltage through a diode. t he maximum value of the startup current is 100ua. for the application of 85vac 264vac, the startup resistor can be calculated by the equatio n : k ua v i v r st in st 850 100 85 max _ min _ ? ? ? constant current control the WS3413H utilizes floating ground structure. the inductor current is sensed during the whole switching cycle, thus it achieves high precision output current control and also excellent line and load regulation. the current in led can be calculated by the equatio n : rcs mv r v i cs cs o 200 ? ? rcs is t he current sensing resistor . feedback network the WS3413H senses the output current zero crossing information through the feedback network, the fb falling threshold voltage is set to 0.2v with 0.15v hysteresis. the fb pin is also used to detect output ovp, the threshold voltage is 1.6v. the ratio of fb upper resistor to lower resistor can be set as: ovp fbh fbl fbl v v r r r 6 . 1 ? ? where, rfbl: the lower resistor of the feedback network rfbh: the upper resistor of the feedback network vovp: output over voltage setting point the minimum vovp should be set about 1.3vo. it is recommended that the fb lower resistor is set to 3.3 k ? 5.1 k paralleled with a 22pf ceramic capacitor. protection functions the WS3413H offers rich protection functions to improve the system reliability. when the led is open circuit, the output voltage will gradually rise up . t he output voltage is sensed by the fb pin when power mosfet is turned off. when fb voltage reaches the ovp threshold, it will trigger fault logic and the system stops switching. when the led is shorted circuit, the system will work under 10k hz switching frequency. meanwhile, the output voltage is low and the vcc pin cannot be charged up by the output voltage, so the vcc pin voltage will gradually decrease and finally reach es the uvlo threshold. after the system enters into fault condition, the vcc voltage will decrease until it reaches uvlo threshold . t hen the system will re-start again. if the fault condition is removed, the system will resume normal operation . when the output is short circuit or the inductor is saturated, the cs peak voltage will be relatively high. when cs voltage reaches the internal limitation (1v), the power mosfet will be turned off instantaneously. this cycle by cycle current limitation can help protecting the power mosfet, the inductor and the output diode. thermal regulation the WS3413H integrates thermal regulation function. when the system is over temperature, the output current is gradually reduced; the output power and thermal dissipation are also reduced. the system temperature is regulated and the system reliability is improved. the thermal regulation temperature is set to 150 internally. pcb layouts the following guidelines should be followed in WS3413H pcb layout:
www.winsemi.com tel : +86-755-8250 6288 fax : +86-755-8250 6299 6 / 8 WS3413H productdescription winsemi microelectronics winsemi microelectronics winsemi microelectronics winsemi microelectronics winsemi microelectronics bypass capacitor the bypass capacitor on vcc pin should be as close as possible to the vcc and gnd pins. ground path the power ground path for current sense resistor should be short and wide, and it should be as close as possible to the ic ground (pin 2 ) , otherwise the led output current accuracy maybe affected . the ic signal ground for comp and fb components should be connected to the ic gnd pin with short traces and should be away from the power ground path. the area of power loop the area of main current loop should be as small as possible to reduce emi radiation. fb pin the feedback resistor divider should be as close as possible to the fb pin , and the trace must keep s away from dynamic node of the inductor (drain pin trace the positive pin and th e negative pin of vo trace) , otherwise the fb pin ovp function might have risk to be mis-triggered by the system noise. d rain pin to i ncrease the copper area of drain pin for better thermal dissipation. however, too large copper area may compromise emi performance. t he material of pcb avoid choosing the material that is easy to absor b the moisture , just like paper copper-clad laminates .
www.winsemi.com tel : +86-755-8250 6288 fax : +86-755-8250 6299 7 / 8 WS3413H productdescription winsemi microelectronics winsemi microelectronics winsemi microelectronics winsemi microelectronics winsemi microelectronics package information dip7 package outline dimensions winsemi symbol dimensions in millimeters dimensions in inches min max min max a 9.00 9.50 0.354 0.374 b 6.10 6.60 0.240 0.260 c 3.0 3.4 0.118 0.134 a1 1.474 1.574 0.058 0.062 a2 0.41 0.53 0.016 0.021 a3 2.44 2.64 0.096 0.104 a4 0.51typ 0.02typ a5 0.99typ 0.04typ c1 6.6 7.30 0.260 0.287 c2 0.50typ 0.02typ c3 3.00 3.40 0.118 0.134 c4 1.47 1.65 0.058 0.065 d 7.62 9.3 0.300 0.366 d1 0.24 0.32 0.009 0.013 d2 7.62typ 0.3typ
www.winsemi.com tel : +86-755-8250 6288 fax : +86-755-8250 6299 8 / 8 WS3413H productdescription winsemi microelectronics winsemi microelectronics winsemi microelectronics winsemi microelectronics winsemi microelectronics n ote: 1. we strongly recommend customers check carefully on the trademark when buying our product, if there is any question, please don't be hesitate to contact us. 2. please do not exceed the absolute maximum ratings of the device when circuit designing. 3. winsemi microelectronics co., ltd reserved the right to make changes in this specification sheet and is subject to change without prior notice. contact: winsemi microelectronics co., ltd. add:futian district, shenzhen tian an cyber tech plaza two east wing 1002 post code : 518040 tel : +86-755-8250 6288 fax : +86-755-8250 6299 web site : www.winsemi.com
|
